Differences

This shows you the differences between two versions of the page.

--- efficiency_now:building_envelope:insulating_a_roller-shutter_box [2023/04/26 16:01] – yaling.hsiao@passiv.de
+++ efficiency_now:building_envelope:insulating_a_roller-shutter_box [2023/08/06 21:39] (current) – wfeist
@@ Line 8: / Line 8: @@
 |<WRAP box 10cm> It is quite easy to cut these panels to size using a sharp knife. A non-compressive low-isocyanate PU adhesive as well as double-sided tape proved suitable for joining these together. </WRAP>|{{:picopen:insulating_roller_shutter_boxes_03.jpg?nolink&400x257|insulating_roller_shutter_boxes_03.jpg}}|
 |<WRAP box 10cm> Double-sided adhesive tape applied to the inner cladding panel of the roller shutter box. </WRAP>|{{:picopen:insulating_roller_shutter_boxes_04.jpg?nolink&400x300|insulating_roller_shutter_boxes_04.jpg}}|
-|<WRAP box 10cm> The cladding panel is now insulated and tape is also applied for protection. The cut-out for the belt can also be seen – a certain amount of leakage will naturally still occur near the opening for the belt, but this is just a single point; and if this is all that remains then the house will already be good :?: wenn das alles ist, was noch verbleibt, dann ist das Haus bereits sehr gut :?: . Of course there are also (relatively) airtight solutions for this as well. </WRAP>|{{:picopen:insulating_roller_shutter_boxes_05.jpg?nolink&400x404|insulating_roller_shutter_boxes_05.jpg}}|
+|<WRAP box 10cm> The cladding panel is now insulated and tape is also applied for protection. The cut-out for the belt can also be seen – a certain amount of leakage will naturally still occur near the opening for the belt, but this is just a single point; and if this is all that remains it's already quite good. Of course there are also even better (relatively) airtight specific solutions for this as well. </WRAP>|{{:picopen:insulating_roller_shutter_boxes_05.jpg?nolink&400x404|insulating_roller_shutter_boxes_05.jpg}}|
-|<WRAP box 10cm> What is far more important is the connection joint of the panel, because its length is more than a metre. A matching sealing strip ("tubular seal") was applied here. The seals used here have proved successful in many applications. They are available in many different materials; for long durability we prefer those made of rubber or silicone ((Some other materials easily become brittle under the influence of UV light)) . The whole thing is then closed again, more than half of the heat losses in this area will be eliminated in this way. </WRAP>|{{:picopen:insulating_roller_shutter_boxes_06.jpg?nolink&400x585|insulating_roller_shutter_boxes_06.jpg}}|
+|<WRAP box 10cm> What is far more important is the connection joint of the panel, because its length is more than a metre. A matching sealing strip ("tubular seal") was applied here. The seals used here have proved successful in many applications. They are available in many different materials; for long durability we prefer those made of rubber or silicone ((Some other materials (e.g. PU) easily become brittle under the influence of UV light)). The whole thing is then closed again, more than half of the heat losses in this area will be eliminated in this way. </WRAP>|{{:picopen:insulating_roller_shutter_boxes_06.jpg?nolink&400x585|insulating_roller_shutter_boxes_06.jpg}}|
 |<WRAP box 10cm> Because this has a complicated multi-dimensional structure, we calculated this using a numerical heat flow software program, "before" (left) and "afterwards" (right). This doesn't just provide a colourful picture but also shows the surface temperature distribution, which is now significantly better, as well as the total remaining heat loss, which is considerably reduced. </WRAP>|{{:picopen:insulating_roller_shutter_boxes_07.png?nolink&400x298}}|