efficiency_now:building_envelope:insulating_a_roller-shutter_box
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| efficiency_now:building_envelope:insulating_a_roller-shutter_box [2023/04/26 15:58] – yaling.hsiao@passiv.de | efficiency_now:building_envelope:insulating_a_roller-shutter_box [2023/08/06 21:39] (current) – wfeist | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Insulating roller shutter boxes ====== | + | ====== Insulating roller shutter boxes ====== |
| + | {{ : | ||
| There just outdoor air inside a roller shutter box - because the gap towards the outside, where the roller shutter exits the box, is permanently open towards the outside. Usually, just a board separates an old roller shutter box from the inside. Heat transmission is particularly high here (2.5 to 4.5 W/(m²K). Making improvements here is relatively easy and also helps a lot. | There just outdoor air inside a roller shutter box - because the gap towards the outside, where the roller shutter exits the box, is permanently open towards the outside. Usually, just a board separates an old roller shutter box from the inside. Heat transmission is particularly high here (2.5 to 4.5 W/(m²K). Making improvements here is relatively easy and also helps a lot. | ||
| - | |<WRAP box 10cm> Usually the cover of the box can be unscrewed towards the inside. There is often a lot of dust gathered inside, this can be cleaned up easily with a vacuum cleaner. Inspect and measure the inner space so that the person carrying out the work knows what size of insulation panels is needed. Because it must be possible to wind and unwind the roller shutter inside the box without striking against anything, there is often very little space available for additional insulation. For this reason we recommend that insulation panels with the lowest possible thermal conductivities should be used here. In this example, 4 cm phenolic foam boards with a thermal conductivity of 0.021 W/(mK) were used. This has a high insulating effect even with less available space. </ | + | |<WRAP box 10cm> Usually the cover of the box can be unscrewed towards the inside. There is often a lot of dust gathered inside, this can be cleaned up easily with a vacuum cleaner. Inspect and measure the inner space so that the person carrying out the work knows what size of insulation panels is needed. Because it must be possible to wind and unwind the roller shutter inside the box without striking against anything, there is often very little space available for additional insulation. For this reason we recommend that insulation panels with the lowest possible thermal conductivities should be used here. In this example, 4 cm phenolic foam boards with a thermal conductivity of 0.021 W/(mK) were used. This has a high insulating effect even with less available space. </ |
| |<WRAP box 10cm> It is helpful to make a sketch showing the surfaces that are to be insulated and how this is to be achieved. Note: also the surfaces at the top and bottom extend from the warm room into the cold roller shutter box, so it makes sense to insulate these as well while you're at it. </ | |<WRAP box 10cm> It is helpful to make a sketch showing the surfaces that are to be insulated and how this is to be achieved. Note: also the surfaces at the top and bottom extend from the warm room into the cold roller shutter box, so it makes sense to insulate these as well while you're at it. </ | ||
| |<WRAP box 10cm> It is quite easy to cut these panels to size using a sharp knife. A non-compressive low-isocyanate PU adhesive as well as double-sided tape proved suitable for joining these together. </ | |<WRAP box 10cm> It is quite easy to cut these panels to size using a sharp knife. A non-compressive low-isocyanate PU adhesive as well as double-sided tape proved suitable for joining these together. </ | ||
| |<WRAP box 10cm> Double-sided adhesive tape applied to the inner cladding panel of the roller shutter box. </ | |<WRAP box 10cm> Double-sided adhesive tape applied to the inner cladding panel of the roller shutter box. </ | ||
| - | |<WRAP box 10cm> The cladding panel is now insulated and tape is also applied for protection. The cut-out for the belt can also be seen – a certain amount of leakage will naturally still occur near the opening for the belt, but this is just a single point; and if this is all that remains | + | |<WRAP box 10cm> The cladding panel is now insulated and tape is also applied for protection. The cut-out for the belt can also be seen – a certain amount of leakage will naturally still occur near the opening for the belt, but this is just a single point; and if this is all that remains |
| - | |<WRAP box 10cm> What is far more important is the connection joint of the panel, because its length is more than a metre. A matching sealing strip (" | + | |<WRAP box 10cm> What is far more important is the connection joint of the panel, because its length is more than a metre. A matching sealing strip (" |
| |<WRAP box 10cm> Because this has a complicated multi-dimensional structure, we calculated this using a numerical heat flow software program, " | |<WRAP box 10cm> Because this has a complicated multi-dimensional structure, we calculated this using a numerical heat flow software program, " | ||
| - | Back to overview of [[.:structural_measures|structural measures.]] | + | Back to overview of [[efficiency_now:building_envelope|structural measures.]] |
efficiency_now/building_envelope/insulating_a_roller-shutter_box.1682517492.txt.gz · Last modified: by yaling.hsiao@passiv.de